HBFITES Data Center, Collaboration, Security, Storage, Wireless, Telepresence Training +91-9886770046 info@hbfites.com

CPT v2.0 - Cisco ONS 15454 Carrier Packet Transport Release 9.5.12

Description

The Cisco ONS 15454 Carrier Packet Transport Release 9.5.12 Version 1 instructor-led course is a lab-intensive course that introduces you to the Cisco Carrier Packet Transport (CPT) network. You will learn about the M6 and M2 shelf hardware installation, power connections, and network connection. You will learn about the CPT 600, CPT 200, and CPT 50 Satellite. The course covers the four kinds of Ethernet virtual circuits (EVCs: Ethernet private line, Ethernet virtual private line, Ethernet private LAN, and Ethernet virtual private LAN). There is a section on how to install connections to an external router network and how to configure EVCs to it. You will learn how to set up the network for Multiprotocol Label Switching (MPLS) Transport Protocol (TP) and install MPLS-TP tunnels, Ethernet pseudowires and virtual private LAN services (VPLS), which are multipoint pseudowire. New to this version of the course are how constant bit-rate services, such as T1 and T3, are carried via EVC and pseudowireand how SyncE is configured in the CPT network. The last section covers integrated dense wavelength-division multiplexing (DWDM), where DWDM is configured in the same chassis with CPT.

Objectives

Upon completion of this course, you should be able to:

  • Connect and configure a Cisco ONS 15454 M6 chassis
  • Install the fanout group connection to the CPT 50 Satellite
  • Install provisionable patch cords between CPT600/200 nodes
  • Configure generic communication channel (GCC) between nodes
  • Create EVCs
  • Install node settings for MPLS-TP
  • Create MPLS-TP tunnels and Ethernet pseudowires
  • Install and test quality of service in the CPT network
  • Create VPLS circuits
  • Install interfaces to external router network
  • Install SyncE in the CPT network
  • Configure T1 circuits using EVC and pseudowire
  • Install integrated DWDM and create satellite links over DWDM network
  • Examine license information in the CPT-50 Satellite
  • Troubleshoot the CPT network

Prerequisites

Following are the prerequisites for this course:

  • Familiarity with the Cisco ONS 15454 family
  • Knowledge of packet switching
  • Knowledge of Ethernet basics

Who Should Attend

This course is for technical professionals who are responsible for installation, deployment, and maintenance of the Cisco 15454 CPT network. Network operations, planners, and designers will also benefit.

Outline

      Module 1: CPT Hardware Fundamentals
      Module 2: CPT Software Fundamentals
      Module 3: Network Configuration Spans, PPCs and GCCs
      Module 4: Configuration for EVCs
      Module 5: Configuration for MPLS-TP
      Module 6: Installing MPLS-TP Tunnels and Pseudowires
      Module 7: Quality of Service for CPT
      Module 8: CPT Virtual Private LAN Service
      Module 9: CPT Router Interface
      Module 10: SyncE and Constant Bit-Rate Circuits
      Module 11: Embedded Dense Wavelength Division Multiplexing
      Module 12: Verifying Satellite License Information
      Module 13: Operations Administration and Maintenance
    Module 14: CPT Troubleshooting

Lab Outline

      Lab 1: CTC Setup
      Lab 2: CPT Setup
      Lab 3: EVC Circuits
      Lab 4: Network Settings for MPLS-TP
      Lab 5: MPLS-TP Tunnels and Ethernet Pseudowires
      Lab 6: Quality of Service
      Lab 7: MPLS-TP Virtual Private LAN Services
      Lab 8: Interface to External Router Network
      Lab 9: SyncE Installation
      Lab 10: T1 over EVC and Pseudowire
      Lab 11: Integrated CPT and DWDM
      Lab 12: Examining Satellite Port License
      Lab 13: CPT Troubleshooting